Lumenline Surface Wall Mount Direct/Indirect
Add to your Selection:
Discreet, linear system for indoor general lighting
The Lumenline Surface Wall Mount Direct/Indirect is part of a linear system of LED luminaires that can be ceiling or wall-mounted to provide a discreet, flexible solution for commercial and institutional environments. These luminaires deliver up to 107 lm/W. Lit corners and a quick joining system allow uninterrupted lines and shapes that blend seamlessly into the architecture. Available in single units or continuous runs, the system offers a choice of outputs (12W/ft or 18W/ft), distributions, colours, colour temperatures, and control options, as well as Legacy or Custom output modes.
Videos
Downloads
Documents (0)
0.00/250 MBSpecification Sheets
Specification SheetPDFdownloadadd
Brochures
Lumenline BrochurePDFdownloadadd
Installation Instructions
Installation InstructionsPDFdownloadadd
Certifications
- UL Certificate of ComplianceZIPdownloadadd
Related Documents
- Continuous Run GuidePDFdownloadadd
- Unlit Joiner GuidePDFdownloadadd
- Submittal Drawings - Shapes With Lit JoinerZIPdownloadadd
- Submittal Drawings - Continuous RunsZIPdownloadadd
- Mounting GuidePDFdownloadadd
- Power and Data Cable Installation GuidePDFdownloadadd
- TM-30 and Spectral Power Distribution GuidePDFdownloadadd
Product Configurator
Your Product Code
LLI2S WM DI __ __ __ __ __ WFL __ __
Mounting
Light Direction
Length
Joiner Type
Direct Lighting Output & Color Temperature 2
Direct Lighting Optics (nominal distribution)
Indirect Lighting Output & Color temperature 2
Indirect Lighting Optics (nominal distribution)
Control
Finish
Notes
- 1 Lumentalk system is enabled with LDB accessory for 1 ft fixture lengths. For white light applications with 1 ft fixtures, DIM or DMX/RDM must be specified in the order code. For RGB applications with 1 ft fixtures, DMX/RDM must be specified in the order code. Lumentalk is not available when RGB direct lighting is combined with RGB indirect lighting. See specification sheet for details.
- 2 Consult factory for 6500K and 90+ CRI.
- 3 RO RGB option requires DMX/RDM or LT control to be specified in control section.
- 4 Not available for RGB color option and lit joiners.
- 5 A DMX Lumentranslator and controller are required for RGB Lumentalk applications.
- 6 10% minimum dimming value. Current Sink: 3mA/fixture, Current Source: 0.5mA/fixture.
- 7 1% minimum dimming value. Available with white light only. Consult Typical Wiring Diagram pages for the number of DALI addresses per fixture length and type.
- 8 A control box (CBX) and LumenID (LID) must be specified.
- 9 1% minimum dimming value. Available with white light only. Fixtures set to by fixture resolution (consult the Resolution Details pages for the number of DMX addresses per fixture length and type).
- 10 Lumenpulse offers a wide selection of RAL CLASSIC (K7) colors with a smooth texture and high-gloss finish. Please consult factory for a list of available K7 colors, other RAL textures and glosses, or to match alternate color charts. Final color matching results may vary.
- 11 Available for NF and WW optics only.
Related Applications
Related Projects
Related Products
-
Lumenline Pendant Direct
-
Lumenline Pendant Regressed Lens Direct
-
Lumenline Pendant Direct/Indirect
-
Lumenline Pendant Indirect
-
Lumenline Recessed
-
Lumenline Recessed Regressed Lens
-
Lumenline Surface Ceiling Mount
-
Lumenline Surface Regressed Lens Ceiling Mount